Friday, July 29, 2011

DIY Hand Held 1.5 Motorized Allspice Shaker


If your looking for that perfect seasoned flavor this gadget offers nothing short of perfection. Powered by
a tiny 1.5  d.c. motor. This project is certainly fun as well as a conversational piece.

View the results of this  Gadget
video

Can you remember your very first cooking experience. I'm sure you can laugh about it now but, if it was anything  like my first cooking venture then you probably ended up at a  fast food restaurant. Don't get me wrong this gadget isn't a replacement of a cook, its' an aide if you can cook! It evenly sprinkles particles from the vibrations of the concealed motor. This gadget allows you to uniquely dispense a
variety of spices by simply removing the twist of cap and adding your spice of choice.

To begin this project you'll need a pepper container.


Remove the original lid from the container so that your container's lid can be modified.


Find a small twist off capped container that will fit comfortably inside of the pepper container. Use a pencil  mark the measurements from the container's lid to the peppers lids'. I used a dremel sanding tool to
accurately make a perfect fit. Afterwards placing the container inside the hole and piecing everything
together like a puzzle.





 

At this point we are semi finished with the lid for now. And focused
on a momentary push button which I drilled a hole in the side of the pepper container that would
accommodate the switch. You can find the switch at a local electronics store or online.


Since the container will consume most of the inside space I elected to use a tiny 1.5 dc motor. You
can purchase them online however, since I was going to upgrade my toothbrush which is electric so why not use use the motor inside of it, so I did.
In my earlier video I chose to mount (solder) the motor on the inside wall of the pepper container. Which is fine
however, Its a little noisy so, my improvement is to zip tie it the motor to the plastic container which absorbs much
of the noise of the motor and at the same time delivers the same or if not better performance needed
to agitate the seasoning container. As you can see in the modified image below.


The switch is coupled directly to the 1.5 dc motor. With the motor and switch mounted and wired I carefully
reassembled the top of the container. After cutting a rectangle in the bottom of the metal pepper container.
I used a demel cutting tool to make the cut.  Before making the modified cut in the pepper container 
I wanted to find a battery compartment to tailor the cut to perfection. Below is a used battery compartment from a used am radio.





With the motor and switch coupled there are only two wires left , the remaining wire from the switch and the remaining wire from the motor. both of these wires will be the connected to the battery power supply holder.


Once the battery compartment connections are made you can begin mounting the battery compartment to 
the pepper container. Before you do you may want to test your battery connections. Even though,
the motor will work no matter which way you connect the wires, it will have 
better agitating effects if the motor is rotating in a counter clockwise fashion . So check before you make
 your connections permanent.


Be sure to recess your battery compartment when mounting so that the container will stand naturally by itself.



Lastly, screw on the container cap and drill holes  positioned as if you are using the gadget.

Tuesday, July 19, 2011

Zipit, Twist and Lock Soda Cap Zip Ties

                                             
          Time Is money so, use your Ties to

                  Save Money!!

 Are you still spending those timely efforts and money to zip tie your most important computer cables just to take that risk of cutting into them just for a simple computer system upgrade. Well, that's now a thought of the past with this simple concept you can use this zip tie over and over again. Just 3 simple items and your're in business. I have been using this for some time and it comes in pretty handy just don't go snooping around in your neighbors  trash for soda bottles lol.

You're going to need these 3 Items:

1. 16oz. soda of your choosing
2. Soldering Iron
3. medium or large zip tie

Using a small hobby saw cut off the top of the soda cap where the colored band separates the cap from the neck of the bottle. Be careful when using sharp and heated tools. In my vid I was cutting free handed however
I suggest using a vice for better control of the saw.



After cutting the cap from the bottle your going to need to remove the colored band from the cap. The
colored band has no purpose for this project and its actually in our working area. I used a small pair of
bandage scissors to remove it.



After removing the colored band, you'll see some uniform gaps that clearly can be seen if you hold the cap in a upright position. These uniform gaps will be imaginary lines when your ready  to heat holes into the cap.
as shown below.





Using your imaginary lines melt 2 slots into the plastic cap one on top of the other. However using the same imaginary line your going to melt a hole on the opposite above the collar of the cap as shown below.



 








 

 Insert a zip tip through the inside of the cap and around the outside underneath the cap and into the top
hole of the cap, and continuing through the opposite side through to the top hole as shown above.


                                                           
                                                  Your done !




Let's try it out







I'm not using them !  I hope this tool will help you




Here are just some items that I use to Zip Tie when organize your accessory affairs. You guys have been
Great thanx!                                                              



       

                                                                               



Thursday, July 7, 2011

Fun with Gadget Games



Keeping Things fun !





If you like  fun games I'm sure you'll like this one.
entangled










Use the M button on your keyboard to mute this Gadget




Play free Games - a game from Puzzle | Logic Games





Tom Neal is a behind the scenes kind of guy. Taking credit for nothing, however his cooperation and contributions have made this blog a worthwhile venture. From all of us to you we say thank you !!




Another one of this sites sponsoring team member who is certainly nothing short of hard working and dedicated. Her community involvement has really made a difference as a positive image to our youth.
 Thanks so much !!